How to remove Dirt and Mud stains
Non-washable Fibers
Learn how to remove dirt and mud stains from Acetate, Burlap, Fiberglass, Rayon, Rope, Silk, Triacetate, Wool:
- Let mud dry, then brush (the method of using a stiff-bristled brush to sweep staining material up onto a piece of paper) off the excess.
- This should remove the stain, but if any remains sponge (the method of using a dampened pad to apply light strokes, moving outward from the center of the stain) the area with water and apply a few drops wet spotter and a few drops white vinegar.
- Cover with an absorbent pad dampened with wet spotter. Let stand as long as any stain is being removed.
- Change the pad as it picks up the stain.
- Keep stain and pad moist with wet spotter and vinegar.
- Flush (the method of applying stain remover to loosen staining material and residue from stain removers) with water and repeat wet spotter/flushing until no more stain is removed.
- If stain remains, apply rubbing alcohol to the area and cover with an absorbent pad dampened with alcohol. (Do not use alcohol on acetate, rayon, or triacetate.)
- Let the pad stand as long as any stain is being removed.
- Change the pad as it picks up the stain.
- Keep the stain and pad moist with alcohol.
- If stain persists, moisten the area with an enzyme presoak (follow directions on label; caution, some enzyme presoaks are not designed for use on silk or wool.)
- Cover with a clean pad that has been dipped in the solution and wrung almost dry. Let it stand for 30 minutes.
- Add enough solution to keep the area warm and just moist.
- When no more stain is being lifted, flush thoroughly with water and allow to dry.
Washable Fibers
Follow these steps to remove dirt and mud stains from Acrylic Fabric, Cotton, Linen, Modacrylic, Nylon, Olefin, Polyester, Spandex:
- Let mud dry, then brush off excess. Laundering should remove any remaining stain.
- If more treatment is needed, sponge the stain with rubbing alcohol. (Do not use alcohol on acrylic or modacrylic.)
- Flush with water. If stain persists, sponge it with a dry-cleaning solvent such as K2r Spot Lifter or Afta Cleaning Fluid.
- Allow to dry, then launder.
Hard Surfaces
Follow these steps to remove dirt and mud stains from Acrylic Plastic, Alabaster, Aluminum, Asphalt, Bamboo, Brass, Bronze, Cane, Ceramic Glass/Tile, Chromium, Copper, Cork, Enamel, Glass, Grout, Iron, Linoleum, Marble, Paint (flat or gloss), Plexiglas, Polyurethane, Porcelain Dishes, Porcelain Fixtures, Stainless Steel, Tin, Vinyl Clothing, Vinyl Tile, Vinyl Wallcovering, Zinc:
- Scrape (the method of using a dull tool to gently lift off excess solid or caked-on stains) any excess with a dull knife or spatula.
- Wipe the surface with a cloth or sponge dipped in warm sudsy water.
- Rinse well and wipe dry.
Stone Surfaces
Follow these steps to remove dirt and mud stains from Bluestone, Brick, Concrete, Flagstone, Granite, Limestone, Masonry Tile, Sandstone, Slate, Terrazzo:
- Carefully remove excess.
- Wash with a solution of washing soda (not soap) and water. Use a cloth or soft-bristled brush to help clean.
- Rinse thoroughly with clear water and allow to dry.
Carpet
Follow these steps to remove dirt and mud stains from carpet:
- To avoid forcing it further into pile, allow mud to dry before treating it.
- Gently brush loose soil, then vacuum as usual. If a stain remains, spray with an aerosol carpet shampoo.
- When the shampoo has dried, vacuum.
Special Fabrics
Follow these steps to remove dirt and mud stains from Felt, Fur (natural or synthetic), Leather, Suede:
- Allow mud to dry, then gently brush off.
- Mix a solution of mild soap in lukewarm water. Swish to create a great volume of suds.
- Apply only the foam with a sponge.
- Wipe area with clean dry cloth.
Comments are closed.